Author Topic: Reinstalling motorized windshield cables  (Read 180 times)

Offline cfry

  • Newbie
  • *
  • Posts: 2
Reinstalling motorized windshield cables
« on: March 24, 2020, 03:21:12 pm »
After reading several threads here I decided to disassemble the motorized windshield to see if the motor was still good or just stuck.  It was stuck and once disassembled the motor works freely as it should.  I've cleaned and lubricated all the pieces and putting it back together.  I'm having a huge challenge getting the cables back on the plastic gear, it's like the cables are short by about an inch.  I'm wondering if any of you have faced this reassembly challenge and if you have any suggestions for getting those cables reconnected. 

Thanks for any help you can give.

Offline VirginiaJim

  • Administrator
  • Elite Member
  • *****
  • Posts: 10832
  • Country: england
  • I've forgotten more than I'll ever know...
    • Kawasaki 1400GTR
Re: Reinstalling motorized windshield cables
« Reply #1 on: March 26, 2020, 06:50:38 am »
I can't say that I've heard of doing that here.  Hopefully someone will chime in.
"LOCTITE┬«"  The original thread locker...  #11  2020 Indian Roadmaster, ABS, Cruise control, heated grips and seats 46 Monitoring with cutting edge technology U.N.I.T is Back! 2008 C14 Moved on to a new home, 2016 RM traded in.

Offline MAN OF BLUES

  • Arena
  • Sr. Member
  • ****
  • Posts: 2817
  • Country: 00
  • WHISKEY.Tango.Foxtrot.
Re: Reinstalling motorized windshield cables
« Reply #2 on: March 26, 2020, 09:29:04 am »
I just looked at the "process" in the FSM.... it's kind of vague, and poorly shown, and thy do make warnings about removing some bolts..

If you don't have an FSM, it's not gonna help, it may just be the cable routings, and the order of which gets slipped in last...   also has to do a lot with the position it was in when removed, down or up?

and which direction you actuated the motor to, when testing...
oh, and which year?

I looked at the '13 FSM...

46 YEARS OF KAW.....  47 years of DEVO..

Offline fartymarty

  • Sr. Member
  • ****
  • Posts: 1571
  • Country: us
  • COG#9712 '10 ABS
Re: Reinstalling motorized windshield cables
« Reply #3 on: March 26, 2020, 01:17:30 pm »
I looked in the SM as well and they seem to treat it as an assembly that's not to be repaired but rather replaced. Might be best to search both forums and see who has worked
on theirs in the past and reach out to them in an email since many have moved on to other bikes and no longer check in here. I hope you took photos as you disassembled it?  ???


Offline maxtog

  • Elite Member
  • ******
  • Posts: 8273
  • Country: us
  • 2011 Silver
Re: Reinstalling motorized windshield cables
« Reply #4 on: March 26, 2020, 06:16:40 pm »
I just looked at the "process" in the FSM.... it's kind of vague, and poorly shown

You just defined the factory service manual :)
Shoodaben (was Guhl) Mountain Runner ECU flash, Canyon Cages front/rear, Helibars risers, Phil's wedges, Grip Puppies, Sargent World seat-low & heated & pod, Muzzy lowering links, Soupy's stand, Nautilus air horn, Admore lightbar, Ronnie's highway pegs, front running lights, all LED, helmet locks, RAM Xgrip, Sena SMH10, Throttle Tamer, MRA X-Creen, BearingUp Shifter, PR4-GT, Scorpion EXO-T1200,etc

Offline maxtog

  • Elite Member
  • ******
  • Posts: 8273
  • Country: us
  • 2011 Silver
Re: Reinstalling motorized windshield cables
« Reply #5 on: March 26, 2020, 06:19:12 pm »
I looked in the SM as well and they seem to treat it as an assembly that's not to be repaired but rather replaced.

Might be that, exactly.  Same problem (but worse) I had with the gas cap- has tons of tiny parts, falls apart easily, and the service manual has ZERO information about putting it back together.  Almost as if they just expect you to throw it away and replace it with another whole gas cap, just because you had to lube it once.
Shoodaben (was Guhl) Mountain Runner ECU flash, Canyon Cages front/rear, Helibars risers, Phil's wedges, Grip Puppies, Sargent World seat-low & heated & pod, Muzzy lowering links, Soupy's stand, Nautilus air horn, Admore lightbar, Ronnie's highway pegs, front running lights, all LED, helmet locks, RAM Xgrip, Sena SMH10, Throttle Tamer, MRA X-Creen, BearingUp Shifter, PR4-GT, Scorpion EXO-T1200,etc

Offline fartymarty

  • Sr. Member
  • ****
  • Posts: 1571
  • Country: us
  • COG#9712 '10 ABS
Re: Reinstalling motorized windshield cables
« Reply #6 on: March 27, 2020, 07:35:56 am »
Almost as if they just expect you to throw it away and replace it with another whole gas cap, just because you had to lube it once.

Well, to be honest, they don't really expect you to do anything with the Service manual. It is written for the dealers service department.
I'm guessing that the gas cap even at it's high price is cheaper to buy than to pay the hourly rate for disassembly and repair, thus the
lack of information. Same for the windshield assembly.