Poll

Vote to be part of the KIPASS BYPASS MOD by BDF

Vote to be part of the buy....
93 (89.4%)
Don't press this button.......
11 (10.6%)

Total Members Voted: 101

Author Topic: KIPASS BYPASS Mod by BDF  (Read 106636 times)

Offline rcannon409

  • Full Member
  • ***
  • Posts: 614
Re: KIPASS BYPASS Mod by BDF
« Reply #270 on: June 10, 2017, 07:48:48 am »
The low battery thing irritated me, too. I felt like the battery would not have been nearly as low had it not kept reminding me how low it really was.

As if soemoen falls in a lake, then spends the next three hours yelling, "I'm drowning"    Well, obviously, you're not, or you would have gone quiet, much earlier.


Offline B.D.F.

  • Hero Member
  • *****
  • Posts: 4731
  • Country: 00
  • It's only really cold if you fall down in it.
    • C-14 farkles you almost cannot ride without.
Re: KIPASS BYPASS Mod by BDF
« Reply #271 on: June 10, 2017, 03:26:23 pm »
OFFTOPIC:

That one I think they actually fixed. Kawasaki used to use an different brand and type of tire pressure sensor, and the low battery flaw was inside that sensor. Now they use Schrader sensors (like everyone else) and I do not believe the Schrader suffer from this problem.

Also, the <base> Schrader sensor is readily available every place that sells or services  tires, and it is cheap. Unfortunately, Kawasaki does not use the basic version but has their own made for them so we cannot just swap ours out for standard Schraders but must use the Schrader sensors that Kawasaki sells.

So I guess this is like a good news / bad news joke. Though the original sensors were also quite expensive. So maybe this is really a bad news / bad news / newer bad news joke.... and it is on us, the C-14 owners. Really, at this point in time when much more reasonable systems are available from third- party manufacturers, it now sort of makes sense to just scrap the OEM sensors (disable them- we still need the valve stem) and use an after market setup. Sure it is an add- on and not built into the bike but then again, most of us have about 83 add- on gizmos all over the place so what is one more discreet thingy stuck to the dash?

Brian

The low battery thing irritated me, too. I felt like the battery would not have been nearly as low had it not kept reminding me how low it really was.

As if soemoen falls in a lake, then spends the next three hours yelling, "I'm drowning"    Well, obviously, you're not, or you would have gone quiet, much earlier.
Homo Sapiens Sapiens and just a tad of Neanderthal but it usually does not show....  My Private mail is blocked; it is not you, it is me, just like that dating partner said all those years ago. Please send an e-mail if you want to contact me privately.

KiPass keeping you up at night? Fuel gauge warning burning your retinas? Get unlimited peace and harmony here: www.incontrolne.com

Offline rcannon409

  • Full Member
  • ***
  • Posts: 614
Re: KIPASS BYPASS Mod by BDF
« Reply #272 on: June 11, 2017, 10:08:24 am »
Great points on the sensor, as usual.

My rear sensor is an original 08 model, and I had no trouble putting  anew battery in it.

When I took my bike to the shop....not sure when this was.  It went to the shop for the removal of that rear brake clevis guard they had installed on the prior visit...maybe 2012?

Anyway, at that time the front sensor was showing "low battery" so they replaced it.  Im afraid that I ended up with the one where you cant get to the battery.

I love Brians products and ideas. Every product has that, "Duh, why didn't I think of that" feel to them.

Offline B.D.F.

  • Hero Member
  • *****
  • Posts: 4731
  • Country: 00
  • It's only really cold if you fall down in it.
    • C-14 farkles you almost cannot ride without.
Re: KIPASS BYPASS Mod by BDF
« Reply #273 on: June 11, 2017, 03:27:15 pm »
Thank you for the kind words. You probably would not love all my ideas though; you have only seen a few of the more polished ones :-)  Some of them..... well, let's just say they cannot be polished and leave it at that.  ;D 

About the new sensor: I believe someone opened one of them and the battery is not actually potted, so while there is some cutting and hacking involved, the batteries can be replaced <reasonably> easily Certainly much more easily than an epoxy potted sensor. Now that assumes I am remembering all of this correctly and the sensor I saw is what Kawasaki is actually supplying. I believe it was in a post on this forum (the only vehicle forum I use so it almost has to be this one) so you can probably find it. Or maybe the original author will chime in with a pointer to his / her original post and photos about it.

Brian


Great points on the sensor, as usual.

My rear sensor is an original 08 model, and I had no trouble putting  anew battery in it.

When I took my bike to the shop....not sure when this was.  It went to the shop for the removal of that rear brake clevis guard they had installed on the prior visit...maybe 2012?

Anyway, at that time the front sensor was showing "low battery" so they replaced it.  Im afraid that I ended up with the one where you cant get to the battery.

I love Brians products and ideas. Every product has that, "Duh, why didn't I think of that" feel to them.
Homo Sapiens Sapiens and just a tad of Neanderthal but it usually does not show....  My Private mail is blocked; it is not you, it is me, just like that dating partner said all those years ago. Please send an e-mail if you want to contact me privately.

KiPass keeping you up at night? Fuel gauge warning burning your retinas? Get unlimited peace and harmony here: www.incontrolne.com

Offline B.D.F.

  • Hero Member
  • *****
  • Posts: 4731
  • Country: 00
  • It's only really cold if you fall down in it.
    • C-14 farkles you almost cannot ride without.
Re: KIPASS BYPASS Mod by BDF
« Reply #274 on: June 29, 2017, 06:17:38 am »
To my non- US customers and potential customers: shipping prices have recently dropped dramatically. I have no idea why this is but what was a common price to ship to many parts of the world overseas was in the $20 to $30 (US) range, which was frankly ridiculous. These were the prices actually charged me to ship my products; I do not tack on any extra for shipping. And of course, a shipping charge of $30 was quite substantial on a $50 retail cost product.

I just got a price to ship to Australia and it was $8 (US) which includes both actual shipping charges as well as exchange rate surcharges. Shipping to Canada has been $5 (US) recently.

I just wanted to let the folks outside the US know that my products are now a lot more reasonable to purchase due to a dramatic decrease in shipping costs.

Brian
Homo Sapiens Sapiens and just a tad of Neanderthal but it usually does not show....  My Private mail is blocked; it is not you, it is me, just like that dating partner said all those years ago. Please send an e-mail if you want to contact me privately.

KiPass keeping you up at night? Fuel gauge warning burning your retinas? Get unlimited peace and harmony here: www.incontrolne.com

Offline Bonsaicat

  • Newbie
  • *
  • Posts: 3
Re: KIPASS BYPASS Mod by BDF
« Reply #275 on: October 23, 2018, 02:30:23 pm »
Why wouldn’t you just remove the switch solenoid? in the ignition

Offline Conrad

  • Hero Member
  • *****
  • Posts: 5720
  • Country: us
Re: KIPASS BYPASS Mod by BDF
« Reply #276 on: October 24, 2018, 06:34:58 am »
Why wouldn’t you just remove the switch solenoid? in the ignition

You're a newbie so I'll go easy.

Did you see how many guys have posted in this thread? Do you think that if the solution to the Kipass issue was as simple as removing the solenoid that someone would have thought of that by now? No, it's not that simple and no, you can't just remove it.
Northern Illinois   Silverdammit '08 C-14 ABS

"Don't bother me with facts, Son. I've already made up my mind." -Foghorn Leghorn

Offline fartymarty

  • Sr. Member
  • ****
  • Posts: 1424
  • Country: us
  • COG#9712 '10 ABS
Re: KIPASS BYPASS Mod by BDF
« Reply #277 on: October 30, 2018, 12:15:41 pm »
Why wouldn’t you just remove the switch solenoid? in the ignition


Different folks consider some work difficult and to others it's just not a big deal as they've been doing it for years and have all the tools and most of the knowledge at hand. The link below shows how Fred Harmon did it years ago, so you can be the judge. I think he just cleaned it and lubed it instead of removing it. Personally I wouldn't do all that until it was an established problem on my bike and it's not something that I'd want to do on a long trip. I think that's the beauty of Brian's product, you simply plug it in the system and it sits silently at the ready to save the remainder of your trip and then get you home where you can either fix it in your garage or take it (ride it in) to the shop. YOMV.

http://www.pbase.com/fredharmon/kipass